Maxim-integrated MAXQ7666 Instrukcja Użytkownika Strona 90
- Strona / 386
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
2.7.2 External Reset
During normal operation, the MAXQ7665/MAXQ7666 devices are placed into an external reset mode by holding the RESET pin low for
at least four clock cycles. If the MAXQ7665/MAXQ7666 devices are in the low-power stop mode (i.e., system clock is not active), the
RESET pin becomes an asynchronous source, forcing the reset state immediately after being taken to logic 0. Once the MAXQ7665/
MAXQ7666 enter reset mode, it remains in reset as long as the RESET pin is held at logic 0. After the RESET pin returns to logic 1, the
processor starts the internal 7.6MHz RC oscillator if necessary and exits the reset state within four clock cycles (Figure 2-9) and begins
program execution at address 8000h.
The RESET pin is an output and an input. If a reset condition is caused by an internal source (such as a brownout reset, watchdog, or
internal reset), an output reset pulse or low level is generated at the RESET pin as long as the MAXQ7665/MAXQ7666 remain in reset.
If the RESET pin is connected to an incompatible external reset circuit, it may not be able to drive the output reset signal. However, if
this occurs it does not affect the internal reset condition.
Because the XT bit in the CKCN register and the HFE bit in the OSCC register are cleared to 0 only on power-on reset, it is possible to
exit an external reset with the clock source set to the high-frequency crystal oscillator. In this case, execution resumes running from
the RC oscillator, and the switchover to the high-frequency oscillator occurs automatically when the crystal oscillator is ready.
2.7.3 Internal System Reset
The MAXQ7665/MAXQ7666 support internal system reset capability from in-system programming mode. An internal system reset is
generated when the ROD bit in the system control register is set. The SPE bit in the ICDF register must also be set. The bootloader
software can use this capability to initiate an internal system reset when the flash loader completes its operation. See
Section 12
for
more details on in-system programming.
MAXQ7665/MAXQ7666 User’s Guide
2-18
Figure 2-9. MAXQ7665/MAXQ7666 External Reset
SYSTEM CLOCK
RESET
RESET
SAMPLING
INTERNAL
RESET
FIRST
INSTRUCTION
FETCH
Maxim Integrated
- Functional Diagrams 1
- 1.1 Overview 7
- 1.1.2 Instruction Set 8
- 1.1.4 Register Space 8
- 1.2 Architecture 9
- 1.2.1 Instruction Decoding 10
- 1.2.2 Register Space 11
- 1.2.3 Memory Organization 13
- 1.2.3.2 Utility ROM 16
- 1.2.3.3 Data Memory 16
- 1.2.3.4 Stack Memory 17
- 1.2.3.7 Data Alignment 19
- CDA0 = 1 21
- 1.2.4 Interrupts 25
- 1.3 Programming 31
- 1.3.6.1 Sign Flag 37
- 1.3.6.2 Zero Flag 38
- 1.3.6.3 Equals Flag 38
- 1.3.6.4 Carry Flag 38
- 1.3.6.5 Overflow Flag 39
- 1.3.7.2 Unconditional Jumps 39
- 1.3.7.3 Conditional Jumps 40
- 1.3.7.4 Calling Subroutines 40
- 1.3.7.5 Looping Operations 40
- 1.3.8 Handling Interrupts 41
- 1.3.9 Accessing the Stack 42
- 1.3.10 Accessing Data Memory 43
- 1.4.19 General Register (GR) 59
- 2.1 Architecture 75
- 2.3 Supply Configuration 83
- 2.4 Linear Regulator 84
- 2.5 Power-On Reset 84
- 2.5.1 Power-Up Counter 85
- 2.5.3 Reset Output 87
- 2.7 Reset Mode 89
- 2.7.2 External Reset 90
- 2.7.3 Internal System Reset 90
- SECTION 3: ANALOG I/O MODULE 91
- 3.1.1 Analog I/O Pins 96
- Register Name: ACNT 98
- ADCMX2 ADCMX1 FUNCTION 99
- 1 1 Reserved 99
- Maxim Integrated 100
- Section 5 104
- Section 2 104
- Section 3.3.6 107
- Section 3.4 107
- Table 3-2. ADC Signals 108
- Section 3.3.10 110
- 3.3.4 Unipolar/Bipolar 111
- 3.3.5 Transfer Function 112
- Section 3.3.3 115
- Section 3.3.5 115
- 3.3.7 Analog Input Protection 116
- 3.3.8 ADC Clock 117
- 3.3.9 Auto Shutdown Mode 117
- 3.3.11 ADC Interrupts 122
- 3.3.12 Using the ADC 123
- 3.4 Temperature Sensor 124
- Sections 15 125
- TEMPERATURE (°C) 126
- Section 3.4.2 127
- Table 3-12. DAC Signals 128
- 3.5.4 DAC Power-Down 130
- 3.5.5 Using the DAC 130
- LIST OF FIGURES 133
- LIST OF TABLES 133
- 4.1 Architecture 134
- 4.2 CAN Controller Registers 136
- 4.3 CAN Operations 177
- 4.3.1.2 Remote Frame 180
- 4.3.1.3 Error Frame 181
- 4.3.1.4 Overload Frame 181
- 4.5 External Pins 182
- 4.7 CAN Interrupts 183
- 4.8.1 Message Center 15 185
- 4.9.2 Receiving Data Messages 186
- 4.15 Bit Timing 194
- 4.16 CAN Bus Activity 197
- 5.1 Architecture 200
- Section 3 204
- 76543210 205
- Reset 0 0 1 0 0 0 0 1 205
- Access rw r r rw rw rw rw rw 205
- 5.3 System Clock Generation 209
- 5.4 Watchdog Timer 215
- 5.5 Power Management Mode 217
- 5.5.2 Switchback Mode 218
- 5.5.3 Stop Mode 218
- SECTION 6: SERIAL I/O MODULE 219
- 6.1.1 UART Pins 223
- 6.2 UART Registers 223
- Serial Mode Definition 224
- — — — — — — — 226
- 6.3 Modes of Operation 227
- 6.3.3 UART Mode 2 230
- 6.3.4 UART Mode 3 230
- 6.4 Baud-Rate Generation 233
- 6.4.4 Baud-Clock Generator 234
- 6.5 Framing Error Detection 235
- 7.1 Architecture 238
- Compare Mode: 244
- Capture Mode: 244
- 7.2.3 Type 2 Reload Registers 248
- 7.3.3 16-Bit Counter 255
- 7.3.4 Dual 8-Bit Timers 256
- 7.4.3 Measure Period 259
- 8.1 Architecture 264
- 8.1.1 Port Pins 265
- 8.2 Port Registers 265
- 8.3 GPIO Operation 271
- 8.3.4 Port Pin Examples 273
- 9.1 Architecture 276
- 9.1.1 SPI Pins 277
- 9.2 SPI Peripheral Registers 277
- 9.3 SPI Operation 282
- 9.3.2 SPI Slave Operation 283
- 9.3.3 SPI Transfer Formats 284
- 9.4 SPI Transfer Baud Rates 285
- 9.5 SPI System Errors 285
- 9.6 SPI Interrupts 286
- 10.1 TAP Overview 289
- 10.2 Architecture 289
- 10.2.1 TAP Pins 290
- 10.3 TAP Interface Control 291
- 10.4 TAP Controller Operation 292
- 10.4.2 Run-Test-Idle 293
- 10.4.3 IR-Scan Sequence 293
- 10.4.5 Communication via TAP 294
- 11.1 Architecture 299
- Section 12 303
- Section 10 305
- Section 1 305
- 11.3 Debug Engine Operation 306
- 11.3.2 Breakpoint Registers 308
- 11.3.3 Using Breakpoints 310
- 11.3.4 Debug Mode 311
- 11.3.5 Debug Mode Commands 311
- 11.3.8 Return 313
- 12.1 Bootstrap-Loader Mode 317
- Section 11 318
- Section 12.5 320
- 12.5 JTAG Bootloader Protocol 321
- 13.6 Operand Count Selection 335
- 13.8 Accessing the Multiplier 336
- Acc.<b> 343
- 1000 1010 0001 1010 345
- 1101 1010 0010 1010 346
- 0011 1100 ssss ssss 349
- 0111 1100 ssss ssss 349
- 1111 1010 bbbb 1010 352
- 1101 1010 0000 1010 353
- 1110 1010 bbbb 1010 353
- 1101 1010 0001 1010 354
- 1ddd dddd 0bbb 0111 354
- 1ddd dddd 1bbb 0111 354
- 1000 1010 1001 1010 355
- .<b> 356
- 1110 1100 0000 1101 359
- 1001 1100 0000 1101 359
- 1101 1100 0000 1101 359
- 1100 1100 0000 1101 359
- 1000 1100 1000 1101 360
- 1010 1100 1000 1101 360
- 1110 1100 1000 1101 360
- 1001 1100 1000 1101 361
- 1101 1100 1000 1101 361
- 1100 1100 1000 1101 361
- 1000 1010 0100 1010 362
- 1000 1010 0101 1010 362
- 1000 1010 1100 1010 363
- 1000 1010 1101 1010 363
- 1000 1010 0010 1010 364
- 1000 1010 0011 1010 364
- 1000 1010 0110 1010 364
- 1000 1010 1010 1010 365
- 1000 1010 1111 1010 365
- 1000 1010 1110 1010 366
- 1000 1010 1011 1010 366
- 1000 1010 0111 1010 368
- 1000 1010 1000 1010 368
- 1011 1010 bbbb 1010 369
- WITH TYPE A FLASH) 371
- 15.2 Data Transfer Functions 372
- TYPE F FLASH) 378
- 16.2 Data Transfer Functions 383
- REVISION HISTORY 386
Powiązane produkty i podręczniki dla Sprzęt komputerowy Maxim-integrated MAXQ7666
Sprzęt komputerowy Maxim-integrated MAXQ Family Users Guide: MAXQ8913 Supplement Instrukcja Użytkownika
(114 strony)
(114 strony)
Sprzęt komputerowy Maxim-integrated High-Speed Microcontroller Users Guide: DS80C390 S Instrukcja Użytkownika
(158 strony)
(158 strony)
Sprzęt komputerowy Maxim-integrated High-Speed Microcontroller Users Guide: Network Mi Instrukcja Użytkownika
(221 strony)
(221 strony)
Sprzęt komputerowy Maxim-integrated Ultra-High-Speed Flash Microcontroller Instrukcja Użytkownika
(169 strony)
(169 strony)
Lincoln Electric IM741 RANGER 250 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Ausrüstung Lincoln Electric IM741 RANGER 250.
Wir stellen 2 PDF-Handbücher Lincoln Electric IM741 RANGER 250 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Komentarze do niniejszej Instrukcji